How To Install Remote Starter Switch

Download Commodity

Download Commodity

Ideally, remote starters should be installed by a qualified technician because improper installation can impairment expensive vehicle control electronics. Yet, for someone familiar with electronics and vehicle repair, knowing how to install a remote starter in a car can save money on installation costs and eliminate the frustration of finding a qualified installer. While this article provides some general instructions for wiring a remote starter, it varies by vehicle and remote starter model.

1. 

   1

   Make certain the remote starter you choose is compatible with your vehicle make and model. Read the box or contact the remote starter manufacturer to determine if it is uniform with your vehicle. You will desire a starter that is compatible with your anti-theft organization and secure.^[1]

   • If information technology is non compatible with your anti-theft system, you will have to buy boosted costly anti-theft featherbed modules.

2. 

   2

   Read the installation instructions advisedly. Installation instructions vary according to dissimilar brands and models of remote starters. It is important to carefully read the installation instructions and find the wiring diagrams for your particular starter.

   • If you choose a used unit or one that does non include directions, check out online instructions earlier making a buy. Make sure the website is like shooting fish in a barrel to employ and has consummate, printable directions and wiring diagrams that clearly show how to install a remote starter in your car.

   Advertisement

3. 

   three

   Read the possessor's manual and repair guides for your vehicle. Get familiar with the wires in your vehicle past looking over the manual and repair guides. Some standard wire connections include the starter, ignition, ability and accessory controls like oestrus and air conditioning, security or alarm system, radio and power locks.

4. 

   4

   Gather all the tools and equipment you will need. Consult your manuals to determine which tools you lot will need for your item starter and vehicle. You may require a utility knife, wire cutters, wire strippers, soldering iron and solder, electrical tape, digital multimeter, wrenches and/or screwdrivers. A digital multimeter is recommended for testing during and after installation.

   • Some remote starters will come with all the necessary tools and then check your box. For example, many systems come up with an LED circuit tester to find the necessary wires for installation.
   • It is recommended that yous solder all your wires together to form better connections. If you choose to solder you will need a soldering iron and safety spectacles.

5. 

   5

   Make up one's mind where to put the main module and open up the area. It must exist in a secure, hidden location that won't crave extending the supplied wires. The usual position is within the lower nuance underneath the steering wheel. This fashion you can connect directly to the ignition wiring.

   • Don't place it in the engine compartment or any surface area where it will be exposed to extreme vibration or heat.
   • Possible alternative locations include spaces above the radio or glove compartment, the center console and to a higher place the dashboard fuse box.

6. 

   half dozen

   Go over the motorcar to make certain everything is working properly prior to installation. Cheque the battery, switches, lights and other systems. If whatever electric systems are not working correctly so you lot should gear up them prior to beginning your installation.^[ii]

7. 

   seven

   Remove the seat where the control module will be installed if possible. Removing the seat will give you more than room to work while installing the system. If you cannot remove the seat then slide the chair all the way backwards.

8. 

   8

   Disconnect the battery. When working on the electrical organisation of your vehicle it is safer to disconnect the battery to preclude whatsoever shocks. To test the wires you will need to have the battery connected but disconnect it while yous are soldering wires together to exist prophylactic. When testing the wiring with the bombardment continued, brand sure yous do not probe whatsoever air handbag excursion. Most of these are encased in a yellow cover for safe.^[3]

   Advertisement

1. 

   1

   Remove the console roofing under the steering wheel. Utilize a screwdriver to remove the panel covering the underside of the steering column. This is where you will access the wires to connect the starter.^[4]

   • If the panel is non attached with screws then yous might require a socket ready to remove nuts securing the panel.
   • Depending on your vehicle you lot may also need to remove the lower steering cavalcade cover to admission the ignition switch harness. If your vehicle has an anti theft arrangement, it is likely that you will need to remove this encompass.
   • If you lot choose to connect your remote starter to other functions such as the door locks and overhead lights so you will need to remove the kick console as well. This is located on the lower left-hand corner of the driver'south foot box.

2. 

   2

   Connect all your wires properly. It is very important that yous deeply connect all your wires. Loose wires can crusade injury or major belongings damage. It is best to solder all your connections to ensure that they are potent. You should also utilise rut shrink tubing where possible and a good quality electrical record where you cannot.

   • To connect wires first strip away most one/two-1 inch (1-two.five cm) of the blanket effectually the wire. If there are two wires then split them and insert the attaching wire between them. Wrap the attaching wire around the stripped wire and solder them together using the soldering iron. Once they are securely attached, wrap electrical tape around the connection and use ties to hold them in place. Lightly tug on the wires to make sure they do non become loose.

3. 

   3

   Connect the ground wire. The footing wire volition be part of the starter and is often blackness. Connect this past screwing through the ring terminal into a make clean, unpainted metallic surface in the boot panel area. This wire is very important for the proper functioning of your vehicle.

   • Because information technology is and so important, it is better to connect the ground wire to a location in the kick panel every bit opposed to beingness close to the ignition switch in the dash. Likewise, it is better to use a separate grounding location to prevent feedback through wiring that may cause computer failures.

4. 

   iv

   Locate the 12V constant wire on the vehicle and attach the power wire of your arrangement to it. The 12V constant wire is the one attached to the bombardment and is usually institute in the bundle of wires fastened to the ignition switch. You can locate this wire by reading the vehicle's transmission and repair guides or testing with the multimeter.^[v]

   • If you meet any xanthous or otherwise noticeable wires, exercise not bear upon them! These are the airbag wires and must non be tampered with or unplugged.
   • To test the power wires using the multimeter attach it to the wire when the machine is off and the central is out of the ignition. Information technology should read around 12V (or the bombardment voltage) constantly.
   • Some vehicles will accept more than ane 12V abiding wire. In this example identify which is fused at a higher number of amps and attach your primary ability wire to this one. If your starter has 2 power wires, adhere the 2nd power wire on the starter to the additional 12V abiding wire.
   • Employ a soldering iron to connect all wires. This keeps them from falling apart and potentially dissentious your vehicle. Add further protection by taping them completely.

5. 

   5

   Detect and attach the accessory wire. The accompaniment wire supplies power to heat and ac controls and supplies 12V when the key is in the first (accessory) position. Adhere the accessory wire on the starter to the accompaniment wire on the vehicle.^[half-dozen]

   • To find this wire adhere the multimeter while the key is in the "off" position. The voltage should be zero in this position. Turn the key into the first position but no farther. If you have found your accessory wire, the voltage will now read around 12V (11.5-14V). Check that the voltage goes to zero 'while' you lot are cranking the engine (it will read 12V earlier and after cranking).^[vii]
   • Some vehicles might have more than i accompaniment wire to control all the functions. In this case employ a relay to connect additional wires.

6. 

   6

   Locate and connect the ignition wire. The ignition wire supplies power to the fuel pump and ignition organization and will be attached to the ignition switch under the steering wheel. The vehicle transmission or repair guides should tell y'all which color this wire should be. Connect the ignition output wire on the remote starter to this wire.^[8]

   • Once you take located this wire you lot can confirm its identity using the multimeter. Attach the multimeter to the wire while information technology is continued to a good ground wire and it should bear witness no voltage. Plow the key to the kickoff position and the voltage should yet read zero. In the second position, earlier starting the car, there should be a voltage displayed on your multimeter. If there is, and so you accept identified the right wire, if not and so you must try again to locate your ignition wire.
   • Some vehicles take more than ane ignition wire. If and so, use a relay to connect all boosted ignition wires.

7. 

   7

   Find and attach the starter wire. This will only show a voltage while the vehicle is beingness cranked, or turned on. It supplies power to the starter solenoid when turning your vehicle on. Connect the starter wire output on your remote starter to this wire by soldering the wires together.^[ix]

   • Locate a potential starter wire to test with the multimeter. The voltage should be goose egg when the primal is in all positions except while cranking the engine. If y'all think yous have constitute the wire, start with the key in position two and then creepo the engine. The voltage should read zero while the key is in position two, show 12V while cranking and then become dorsum to zero if you release the key before the engine turns over.^[10]

8. 

   eight

   Connect the parking calorie-free and brake wires. The brake wire is ordinarily found at the switch harness above the brake pedal but tin can likewise be found along with the parking light wires in the kick panel on the fashion to the rear of the vehicle. Connect these wires to the parking low-cal and brake output wires on the remote starter.^[11]

   • To find the brake wire press the brake pedal down while the car is on and use the multimeter to exam the wire. The multimeter should read between 11.5-14V while the brake is pressed down.
   • The brake wires in particular are important to connect because they foreclose someone from driving off in your car while information technology is running from the remote starter.

9. 

   9

   Locate and connect the tachometer wire to the tachometer output wire on the remote sensor. This is required by the remote starter and so that it disengages the starter in one case the machine has started. Information technology tin ordinarily be found in the engine distributor or coil pack.^[12]

   • To locate the tachometer wire look for the engine benefactor by post-obit the spark plug wires to where they junction at a distributor and find a small wire harness which should have a tachometer reference. Alternatively see the owner'south transmission to determine the recommended tachometer wire'due south location.

10. 

    x

    Connect any security, anti-theft and other optional components. Some systems might accept additional steps for connecting to the door locks of the vehicle. Others might need a special system for getting around the anti-theft system that exists in your motorcar. As e'er consult the manual or manufacturer of your remote sensor to find out which extra features your system has and where you lot should connect them.

    • To connect to the door locks you can locate the wires in the commuter's side door. You may need an external relay, of which there are many dissimilar kinds. However the four virtually common include positive trigger, negative trigger, reverse polarity and multiplex door lock systems. Consult your vehicle manual or repair guides to determine which system your vehicle uses.

11. 

    xi

    Employ a relay to connect additional wires if in that location is more than one wire for power, accessory or the starter. A relay allows multiple wires to exist connected together. In that location are many different designs, shapes and sizes only they all perform the same basic function. Connect the wires to the relay by wrapping them effectually the pins.

12. 

    12

    Secure wires with tie wraps or screws to continue them away from moving parts. This will protect the wires and make the installation wait tidy and groovy.

13. 

    13

    Connect the battery and test to see that all the functions piece of work. Test your remote offset and keyless entry systems equally well equally your brakes and brake lights to make sure everything has been continued properly and is working. If something fails to work, go back and cheque all the wires you lot have connected to see what went wrong.

    • Make certain y'all test your vehicle to make sure it will start, run, and drive using your fundamental normally. This will insure the installation did not affect any normal vehicle operations or cause any dash lights to illuminate abnormally.

14. 

    14

    Replace the kick panel and the panel covering the ignition switch. Push the remote sensor and the wiring into the compartment and cover with the panel. Screw (or ratchet) the panel into place. Make sure not to pinch or screw into any wiring during installation.

    Advertisement

Add New Question

• Question

  When my remote starter is on, the park lights exercise not turn on. What does that mean? And how do I fix information technology?

  

  Check your parking lights connection - that seems to be the just possible problem unless you take a faulty arrangement.

• Question

  Volition the installation of the remote starter void the manufacturer'southward warranty if non installed by the dealership?

  

  Yes, almost manuals state that this organization is required to exist installed by a professional person.

• Question

  Is it necessary to connect a remote starter to any other components of my car?

  

  No, you don't need to connect the remote starter to whatsoever other components after following the instructions here.

• Question

  After installing the remote starter, my car seems to be struggling to have enough ability to run the engine and electronics, but if I use the normal start this does not happen. What should I do?

  

  The organisation may be either drawing too much power, or, when you use the remote start, the engine may start, merely non generate enough power. Become it checked out from a certified dealer.

• Question

  Why did my bank check engine light come up on after doing this?

  

  In that location are different things that can crusade a bank check engine light to plough on. It may not have anything with the remote starter. You lot should go to a car identify that tin employ a special diagnostic tool to find out. Many car places, including Auto Zone, volition practice this for free.

• Question

  How practise I tell if a vehicle already has a remote starter?

  

  Wait on the windshield, near probable close to the rear-view mirror. If there's a remote starter, there'll be a component similar to the object in the man'due south hand from Stride ten. That's the sensor that receives the signal from the key fob.

Inquire a Question

200 characters left

Include your e-mail address to go a message when this question is answered.

Submit

Advertisement

Video

• Keep wires away from sharp objects nether the dashboard. If a wire is cut or becomes loose information technology tin can cause damage to the vehicle that may be expensive to repair.

• The installation of the remote start system on newer vehicles that have factory security systems and lawmaking keys may require specialized equipment that are only available to the dealers. Brand certain you have complete directions, proper tools and whatsoever specialized equipment earlier attempting installation.

• Take your fourth dimension and exist methodical. It is very important to exist thorough so that you practise not injure yourself or impairment your vehicle.

• Soldering your wires together volition make them more secure and less likely to cause issues in the future.

• Exercise not effort and use a remote beginning arrangement not designed to work with your vehicle.

• Use a relay to connect additional wires if there is more than than one wire for power, accessory or the starter.

Advertisement

• Be careful when working with electric wires equally they can stupor you and cause injury.

• Failure to install your remote sensor correctly can cause injury and property harm.

• Do not operate your remote start system in a closed garage or a buildup of carbon monoxide gas will occur.

• If you are unsure or unfamiliar with electrical systems, do not effort to install your remote starter system on your ain. It is much meliorate and safer to hire a qualified technician to consummate the installation.^[xiii]

Advertizing

Things You'll Need

• Utility knife
• Wire cutters
• Wire strippers
• Soldering iron and solder
• Electric record
• Oestrus compress tubing
• Heat gun
• Digital multimeter
• Wrenches
• Screwdrivers
• Vehicle wire diagrams

About This Article

Article Summary 10

To install a remote starter in a machine, disconnect the bombardment and remove the panel roofing nether the steering wheel. Next, connect the starter's black ground wire to the kick panel and solder the starter's power wire to the 12V wire fastened to the car bombardment. Attach the accessory wire, then connect the ignition wire to the ignition output wire on the remote starter. Lastly, attach the starter wire and connect any security components you have. For tips on keeping wires tidy, read on!

Did this summary assist you?

Thanks to all authors for creating a page that has been read 475,269 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Remote-Starter-in-a-Car

Posted by: morrisfromeannown.blogspot.com

Share this post